Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
DIY Heating Pad for Germinating Plants
DIY Heating Pad for Germinating Plants. Most seeds require heat to germinate, particularly warm-weather annuals such as garden tomatoes (Solanum lycopersicum) and petunias (Petunia x hybrida), which only germinate in temperatures between 70 and 80 degrees Fahrenheit. Even after the seeds have sprouted, little seedlings often need additional heat...
Most seeds require heat to germinate, particularly warm-weather annuals such as garden tomatoes (Solanum lycopersicum) and petunias (Petunia x hybrida), which only germinate in temperatures between 70 and 80 degrees Fahrenheit. Even after the seeds have sprouted, little seedlings often need additional heat when you start them early in the year. Bottom heat is typically recommended for supplying additional heat, either in the form a commercially available heating pad designed for seed starting or as part of a do-it-yourself project.
Things You'll Need
Plywood plank, 1 inch by 12 inches by 4 feet
2 wood furring strips, 1 inch by 2 inch by 8 feet
#6 wood screws, 1 1/2 inches
18-foot incandescent rope light for outdoor use
Cable staples
Tape measure
Hand saw or jigsaw
Hammer
Sandpaper
Cut the furring strips into four 40-inch lengths. Use sandpaper to smooth out any rough edges.
Space 40-inch furring strips evenly across the plywood plank, 4/5 inch apart and 4/5 inch in from each side of the plank.
Attach the furring strips to the plank using wood screws. Place one wood screw 1 inch in from each end of the strips, and three more screws about 12 inches apart down the length of each strip.
Remove the 18-foot rope light from the package and uncoil it. Straighten the rope light out so it's easier to work with.
Place the end of the rope light without the plug at one corner of the board. Run the rope light down along one side of the first furring strip and back up the other side. Continue running the rope along the sides of each furring strip, in a winding position, until you get to the end of the last one.
Secure the rope lights with cable staples. Hammer each staple in far enough to hold the lights, but not enough pinch them or cause an indentation.
Plug in the rope lights, and place seed flats on top of the furring strips. The lights will take approximately 35 to 40 minutes to fully heat up.
Tips & Warnings
Do not use LED rope lights instead of incandescent lights. They do not generate enough heat to start most seeds.
Most plants germinate best in a temperature range between 65 and 75 degrees F. Use a soil thermometer to check the temperature, and unplug the rope lights if the soil gets too hot.
Use only rope lights designed for outdoor use. Indoor rope lights are not waterproof.
