Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Build a Butter Bean Sheller
How to Build a Butter Bean Sheller. A form of Lima beans, butter beans grow in pods that are unpalatable. Removing butter beans from their pods can be done in a variety of ways. Hand shelling involves sticking both thumbs into the seam between the two halves of the pod and pulling the halves apart. Industrial farms and canneries use a bean...
A form of Lima beans, butter beans grow in pods that are unpalatable. Removing butter beans from their pods can be done in a variety of ways. Hand shelling involves sticking both thumbs into the seam between the two halves of the pod and pulling the halves apart. Industrial farms and canneries use a bean threshing device that agitates and beats the pods until they split and release their beans. These devices work well for large crops, but are bulky and unsuitable for a small home garden or shelling enough beans for a single meal.
Things You'll Need
Scrap lumber 2-by-4 inches
Saw
Ruler
Drill
Drill bit 1 inch
2 X-acto knife blades
Needle nose pliers
Hammer
Tin snips
Sandpaper
Square one end of the scrap 2-by-4 inch lumber. Measure 2 inches from the squared end and cut. You will have a 2-by-2-by-4 inch block of wood.
Find the center point of one of the 2-by-4-inch sides with the ruler. Mark the point.
Attach the 1-inch drill bit to the drill. Using the marked point as a guide, drill a 1-inch hole completely through the block of wood.
Rotate the block. Mark the center of the next 2-by-4 inch side directly over the newly drilled hole. Flip the block over and mark the opposite side. These marks now designate the top and bottom of your bean sheller.
Holding the X-acto blade with needle nose pliers, place the tip of the blade on the mark. Line up the blade so that it is aligned with the hole drilled through the block.
Press the tip of the blade into the wood. Tap on the back of the blade with the hammer. Pound the blade into the wood until the tip of the blade emerges in the hole drilled through the block. Cut off the back portion of the blade left on top of the block. Sand any metal sticking out of the wood until the block is smooth. Flip the block over and repeat with the other side.
Insert a bean pod through the hole and pull the end out the other side. The bean pod is slit along both sides and the beans fall free of their hull.
Tips & Warnings
Hold the block of wood securely when inserting the X-acto blades. The wood can be held in a vise if needed.
Use great care when inserting and cutting the X-acto blades. Dispose of the cut pieces properly, they are sharp.
