Bulbs
Flower Basics
Flower Beds & Specialty Gardens
Flower Garden
Garden Furniture
Garden Gnomes
Garden Seeds
Garden Sheds
Garden Statues
Garden Tools & Supplies
Gardening Basics
Green & Organic
Groundcovers & Vines
Growing Annuals
Growing Basil
Growing Beans
Growing Berries
Growing Blueberries
Growing Cactus
Growing Corn
Growing Cotton
Growing Edibles
Growing Flowers
Growing Garlic
Growing Grapes
Growing Grass
Growing Herbs
Growing Jasmine
Growing Mint
Growing Mushrooms
Orchids
Growing Peanuts
Growing Perennials
Growing Plants
Growing Rosemary
Growing Roses
Growing Strawberries
Growing Sunflowers
Growing Thyme
Growing Tomatoes
Growing Tulips
Growing Vegetables
Herb Basics
Herb Garden
Indoor Growing
Landscaping Basics
Landscaping Patios
Landscaping Plants
Landscaping Shrubs
Landscaping Trees
Landscaping Walks & Pathways
Lawn Basics
Lawn Maintenance
Lawn Mowers
Lawn Ornaments
Lawn Planting
Lawn Tools
Outdoor Growing
Overall Landscape Planning
Pests, Weeds & Problems
Plant Basics
Rock Garden
Rose Garden
Shrubs
Soil
Specialty Gardens
Trees
Vegetable Garden
Yard Maintenance
How to Replace Blades on a RZT 54 Cub Cadet
How to Replace Blades on a RZT 54 Cub Cadet. The grass-cutting blades on a Cub Cadet residential zero turn, or RZT, have a 54-inch cutting width. The cutting blades can become dull over time, especially if the area being mowed contains thick plants or weeds. Cub Cadet recommends keeping the blades sharp at all times and sharpening evenly to...
The grass-cutting blades on a Cub Cadet residential zero turn, or RZT, have a 54-inch cutting width. The cutting blades can become dull over time, especially if the area being mowed contains thick plants or weeds. Cub Cadet recommends keeping the blades sharp at all times and sharpening evenly to maintain balance. To sharpen the blades, the cutting deck must be removed; this is a fairly simple and straightforward task.
Things You'll Need
5/16-inch open-ended wrench
Block of wood
Torque wrench
Deck and Pulley Removal
Park the mower on a level surface. Disengage the power take-off, or PTO, switch located to the right of the seat; turn the engine off and engage the parking brake.
Locate the PTO pulley on the bottom of the engine. Raise or lower the deck with the deck height-control lever to a position where the PTO pulley is level with the idler pulleys on top of the deck.
Pull the idler bracket, located in the center of the deck, backward; this will extend the tension spring and loosen the pulley belt. Lift the belt up and over the idler pulley. Slide the belt off the PTO pulley.
Lower the deck to its lowest setting with the deck height-control lever. Locate the deck support pins to the left and right sides of the deck. Pull the pins out of the deck lift arms.
Raise the deck to its highest position with the deck height-control lever to release the deck lift arms from the hanger brackets.
Slide the deck forward and lift the hanger out of the front deck bracket. Slide the deck backward, then sideways to the right and out from under the mower.
Blade Removal
Flip the deck over.
Place a block of wood between the deck housing and the edge of the blade to prevent the blade from turning.
Turn the nut in the center of the blade counterclockwise with a 5/16-inch open-ended wrench; lift the nut off and remove the blade from the spindle. Repeat this procedure to remove all three blades.
Blade Replacement
Install the new or sharpened blade onto the spindle assembly.
Replace the retaining nut and tighten it to 70 to 90 "ft-lbs" torque with a torque wrench. Repeat this procedure for all three blades.
Flip the deck over. Hold the front deck hanger up and slide the deck under the mower from the right side. Slide the deck forward and place the front deck hanger into the front deck hanger bracket.
Slide the deck backward and lower the deck height-control lever. Align the deck lift arms with the rear deck hanger brackets. Pull the deck support pins outward; then push the pins into the deck hanger bracket on each side of the deck to secure the lift arms.
Deck and Pulley Replacement
Raise the deck to a position where the PTO pulley is level with the deck idler pulleys on top of the deck. Install the belt around the PTO pulley.
Route the belt around the idler pulleys on top of the deck.
Pivot the idler bracket in the center of the deck backward, then slide the belt around the idler bracket. Release the idler bracket to tension the pulley belt.
